pfSense 1.2.2はまったく問題なく動作していたが、機能が多く単にFirewallだけであれば、m0n0wallで十分だろうというこで、再度m0n0wallでチャレンジしてみた。最新のバージョン(1.3b15)で失敗したため、1.2系の最新(1.235)で動かしてみたところ、まったく問題なく動作してた。起動も早く軽く、しばらくこれを使ってみる。
起動ログです。
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE-p26 #0: Fri Aug 8 20:42:40 CEST 2008
root@fb411.neon1.net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel (R) Celeron (TM) CPU 1300MHz (1295.80-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff
real memory = 268369920 (262080K bytes)
avail memory = 243466240 (237760K bytes)
Preloaded elf kernel "kernel" at 0xc1106000.
Preloaded mfs_root "/mfsroot" at 0xc110609c.
Pentium Pro MTRR support enabled
md0: Preloaded image 12582912 bytes at 0xc0504e1c
md1: Malloc disk
Using $PIR table, 10 entries at 0xc00fded0
npx0: on motherboard
npx0: INT 16 interface
pcib0: on motherboard
pci0: on pcib0
pcib1: at device 1.0 on pci0
pci1: on pcib1
pcib2: at device 30.0 on pci0
pci2: on pcib2
fxp0: port 0xc000-0xc03f mem 0xd5000000-0xd501ffff,0xd5083000-0xd5083fff irq 9 at device 4.0 on pci2
fxp0: Ethernet address 00:d0:68:04:22:66
inphy0: on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: port 0xc400-0xc43f mem 0xd5020000-0xd503ffff,0xd5081000-0xd5081fff irq 12 at device 5.0 on pci2
fxp1: Ethernet address 00:d0:68:04:22:67
inphy1: on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp2: port 0xc800-0xc83f mem 0xd5040000-0xd505ffff,0xd5080000-0xd5080fff irq 11 at device 6.0 on pci2
fxp2: Ethernet address 00:d0:68:04:22:68
inphy2: on miibus2
inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp3: port 0xcc00-0xcc3f mem 0xd5060000-0xd507ffff,0xd5082000-0xd5082fff irq 10 at device 10.0 on pci2
fxp3: Ethernet address 00:d0:68:04:22:69
inphy3: on miibus3
inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: at device 31.0 on pci0
isa0: on isab0
atapci0: port 0xf000-0xf00f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: port 0xd000-0xd01f irq 10 at device 31.2 on pci0
usb0: on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: port 0xd400-0xd41f irq 5 at device 31.4 on pci0
usb1: on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
orm0: at iomem 0xc8000-0xcbfff on isa0
pmtimer0 on isa0
fdc0: at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
atkbdc0: at port 0x60,0x64 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized. Default = block all, Logging = enabled
ad3: 1911MB [3884/16/63] at ata1-slave PIO4
Mounting root from ufs:/dev/md0c
kern.coredump: 1 -> 0
Found configuration on ad3.
Initializing timezone... done
Initializing PC cards... failed (probably no PC card controller present)
Configuring firewall... done
Configuring LAN finterface... xp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
done
Configuring WAN interface... done
Configuring OPT1 (OPT1) interface... done
Configuring OPT2 (OPT2) interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting DHCP service... done
Starting NTP client... done
*** This is m0n0wall, version 1.235
built on Thu Sep 4 21:49:29 CEST 2008 for generic-pc
Copyright (C) 2002-2008 by Manuel Kasper. All rights reserved.
Visit http://m0n0.ch/wall for updates.
LAN IP address: xxx.xxx.xxx.xxx
Port configuration:
LAN -> fxp0
WAN -> fxp3
OPT1 -> fxp1 (OPT1)
OPT2 -> fxp2 (OPT2)
m0n0wall console setup
**********************
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host
Enter a number: